- HOW TO DISABLE TERADICI PCOIP SOFTWARE
- HOW TO DISABLE TERADICI PCOIP LICENSE
- HOW TO DISABLE TERADICI PCOIP WINDOWS
When this setting is disabled or not configured, no minimum bandwidth is reserved. The default value is 0, which means that no minimum bandwidth is reserved. Make sure that the sum of bandwidth floors for all connections in your configuration does not exceed the network capability. Make sure that you do not over-subscribe the total reserved bandwidth for all endpoints. When you use this setting to reserve bandwidth for an endpoint, the session does not have to wait for bandwidth to become available, which improves session responsiveness. This setting configures the minimum expected bandwidth transmission rate for the endpoint. Specifies a lower limit, in kilobits per second, for the bandwidth that is reserved by the PCoIP session. Configure the PCoIP session bandwidth floor ¶ Directive If this setting is disabled or not configured, the client uses the default value in the negotiation with the agent. If the two endpoints have different MTU size settings, the lowest size is used. This setting applies to the agent and client. Change this value if you have an unusual network setup that causes PCoIP packet fragmentation. Typically, you do not have to change the MTU size. TCP uses the standard MTU discovery mechanism to set MTU and is not affected by this setting. The MTU size includes IP and UDP packet headers. Specifies the Maximum Transmission Unit (MTU) size for UDP packets for a PCoIP session. This setting takes effect when you start the next session. Configure the PCoIP session MTU ¶ Directive If the two endpoints have different settings, the lower value is used.
The default value when this setting is not configured is 900000 kilobits per second. When this setting is configured, the setting is used as the endpoint's maximum bandwidth constraint in kilobits per second. When this setting is disabled or not configured on an endpoint, the endpoint imposes no bandwidth constraints. For example, setting a 4Mbit/s maximum bandwidth forces the agent to transmit at a lower rate, even though the setting is configured on the client. It forces the client and agent to use the lower of the two values that are set on the client and agent side. Setting this value prevents the agent from attempting to transmit at a higher rate than the link capacity, which would cause excessive packet loss and a poorer user experience. a single PCoIP session) that connects through a 4Mbit/s Internet connection, set this value to 4Mbit (or 10% less than this value to leave some allowance for other network traffic). For example, with a single user VDI configuration (e.g. Set this value based on the overall capacity of the link to which your endpoint is connected, taking into consideration the number of expected concurrent PCoIP sessions. The bandwidth includes all imaging, audio, virtual channel, USB, and control PCoIP traffic. Specifies the maximum bandwidth, in kilobits per second, in a PCoIP session. Configure the maximum PCoIP session bandwidth ¶ Directive
If this setting is Enabled then the build-to-lossless feature is turned on this is recommended for environments that require images and desktop content to be built to a lossless state. In network environments with constrained bandwidth, turning off the build-to-lossless feature can provide bandwidth savings. If this setting is Disabled or Not Configured then the build-to-lossless feature is turned off and images and other desktop content may never build to a lossless state. Specifies whether to turn the build-to-lossless feature of the PCoIP protocol off or on this feature is turned off by default.
HOW TO DISABLE TERADICI PCOIP SOFTWARE
Managing Licenses with the PCoIP Control PanelĮnable Software Secure Attention Sequence (SAS)Ĭonfigurable Settings ¶ Configure build-to-lossless ¶ Directive
HOW TO DISABLE TERADICI PCOIP WINDOWS
Viewing Agent Logs in Windows Event Viewer
HOW TO DISABLE TERADICI PCOIP LICENSE
Configure the maximum PCoIP session bandwidthĬonfigure the PCoIP session bandwidth floorĮnable/disable audio in the PCoIP sessionĬonfigure the PCoIP session audio bandwidth limitĬonfigure PCoIP Security Certificate SettingsĬonfigure PCoIP USB allowed and unallowed device rulesĬonfigure Session Automatic Reconnection PolicyĬonfigure Proxy Access to a remote License ServerĬonfigure PCoIP session SSO access control